Showing results: 571 - 585 of 1099 items found.
-
WEETECH, INC.
WEETECH, as a manufacturer of test equipment, offers its customers also a "Ready To Use" test system solution. It consists of the test table, the customer-specific adaptation as well as the test device, and is very quickly ready for use at the customer's site. According to the customer's requirements, the set-up is designed as a system with permanently installed adaptations for the production of constant cable harnesses in large quantities or with interchangeable adapters for the flexible production of different cable harnesses. Depending on the application, a larger table version or a smaller desk version is available. Various interfaces are available for integrating these solutions into a complete production automation system.
-
KMF 1 -
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR KMF 1. The KMF 1 search receiver is used according to the step voltage method. The cable line is scanned with two measurement probes that can be dismantled during transport. The battery-operated device is also suitable for locating multiple consecutive sheath faults.* Battery mode* Zero point compensation* accurate location of cable sheath faults* battery test
-
Fairview Microwave Inc.
Low-PIM jumper cables feature a maximum PIM level of -155 dBc and are made with UL910 plenum-rated SPP-250-LLPL cable. The PIM levels of each cable have been fully tested with the results of those tests marked on each cable. These Low-PIM cables boast a maximum operating frequency of 6 GHz and a maximum VSWR of 1.25:1 up to 2 GHz and 1.35:1 up to 6 GHz. These Low-PIM cables are lightweight, flexible and have an operating temperature range of -55°C to +125°C and are available with 4.3-10, 7/16 DIN, N and 4.1-9.5 mini-DIN connector combinations, including right-angle connectors.
-
ZhangZhou Weihua Electronic co.,ltd
There is nothing worse than running your drops only to learn that you have a fault in one of the cable runs. Get it right the first time, get it right by choosing and using the right LAN Cable Testers. We offer a variety of cable testers, which are a must have to quickly and easily verify the integrity of Ethernet twisted pair cables. Our LAN testers will test twisted pair cables for open pairs, shorted pairs, reversed pairs, crossed pairs and split pairs. Network cable testers vary in complexity and price, but a basic tester consists of a source of electrical current and a measuring device. After that, cable testers vary in complexity and ability to do various testing.
-
Technology Products
This Compact power supply/test set can perform all laboratory and field tests of DC Hipot. A flexible High Voltage Cable is provided at the back for connecting to the test specimen. Available in Rack Mount as well as portable design.
-
DCOAX -
Andeen-Hagerling, Inc.
Very high precision, three-terminal capacitance measurements can be affected by the self-inductance of the test cables, mainly at higher capacitance values. Magnetically induced noise can also reduce the quality of measurements. The cable now offered by Andeen-Hagerling both minimizes these problems and provides a way to standardize the residual self-inductance.
-
AVJoG Rack -
CableJoG Ltd
*A single box solution for testing AV cables. *Easy to use with only one button operation. *Detects Open, Short and Crossed circuits. *LCD display for test results. *All major AV connectors present, no need for extra adaptors. *40+ preprogrammed cable types.
-
CableJoG 1024 -
CableJoG Ltd
The CableJoG 512 and CabeJoG 512 Plus provide a flexible testing system to suit individual customer requirements. The CableJoG 512 and CableJoG Plus 512 can test up to 1024 individual connections of all manufacturers of connectors. This simple to use test instrument stores up to 59 separate cable configurations. Each cable that is tested is compared against the stored details to produce a pass, fail, open/short/crossed indication.
-
PA-40 -
Pansco, Ltd
The PA-40 is designed to check both shielded and unshielded twisted pair (STP/UTP) and coaxial BNC-type network cables. With the push of a button, it tests all wires for continuity, miswiring, and polarization. Dual-colored LEDs let you identify correct and reversed pairs; using the included remote unit, cables may be tested before installation or after installation. Features tip/ring polarity test. Uses 1 9V battery.
-
Crest Test Systems Pvt. Ltd.
HV Test, which is also known as Hipot Test – short form of high potential – is used to test the insulation quality of the auxiliary circuit of circuit breakers. The HV Test is useful in finding damaged insulation, stray conductive materials around the conductors, and problems due to terminal spacing and tolerance errors in cables.
-
Liona -
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR liona. Liona is a portable online PD spot tester for measuring and locating partial discharges in cables and switchgear during normal mains operation. Liona lets you test cable systems and electrical equipment online without switching off partial discharge activities, and then generate trend analyses. Even a PD spot test (duration: 5-10 minutes) is capable of reliably assessing the current status of your system.* Automatic PD detection during normal mains operation (without switching off the cable route)* With DeCIFer technology: PD identification based on 500 million measurement results* Precise online PD mapping with PD transponder
-
72-8495 -
Tenma
Compact 2-in-1 unit provides standard digital multimeter functions, as well as pin configurations on network and voice cables. Dual pinout indicator provides sequential verification of each pin on a network cable, and the included remote terminator allows testing of cables which are already installed. Digital multimeter measures AC/DC volts and amps, resistance and diodes, and provides audible continuity test.
-
Spectrum Instrumentation
Adapter Cables connect your Spectrum card or instrument with your device under test, your sensor, your transmitter or receiver, your external machine, your prototype equipment or simply with a probe for measuring. To fulfill a lot of different requirements Spectrum is offering adapter cables between different types of connections and with different length. These adapter cables are manufactured for Spectrum following Spectrum's specification.
-
Yangzhou Power Electric Co., Ltd
High current test systems are used to test the thermal stability of equipment and components. The test system induces a current in the test object causing it to heat up.The system can perform the heat cycle testing for power cables type test and pre-qualification test according to IEC 60840, and IEC 62067 etc. Based on pre-qualification test needs, test system is divided into two parts: test sample loop and simulation temperature loop.
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Altitude & Temperature Test Chamber combine Altitude and temperature to test various components and products, especially the aircraft avionics. Automatic controlled vacuum system provide a precise altitude simulated condition up to 30000 meters. Available to connect cable for the electronic performance test.
